Aluminum Flashing Steady LED Brake Light by Top Serve LLC

Aluminum Flashing-Steady LED Brake Light
by Top Serve LLC

Product Details

Do you wonder how well other drivers are paying attention to you in your vehicle while braking? This Flashing-Steady LED Brake Light increases your visibility to add additional safety and awareness to you.

The Flashing-Steady LED Brake Light has been developed to provide an eye catching third brake light, especially designed to attract attention to you and your vehicle while braking. It has been designed for easy installation and detachment. For example, if you would like to remove it during an auto show event. It has been designed to operate for both vintage and modern vehicles. It only draws 100 ma, and it operates on 6 and 12 volt electrical systems, positive or negative grounds. It is completely encased with epoxy inside aluminum channel, making it durable, rugged, and completely weather proof. The light measures 8-1/4" long, 15/16" tall, and 3/4" thick.

LED Brake Light Side

The Flashing-Steady LED Brake Light grabs attention by pulsing its 10, 10 mm dia. superbright red LEDs and then goes to a steady on state. Every time power is applied, it flashes for a set period and then goes to a steady on. The Aluminum Flashing-Steady LED Brake Light is available in several different flashing periods. Preset flashing periods of 2 seconds, 4 seconds, and 6 seconds are available. Steady on only, is also available. If you desire a different flashing period, please contact topserve@tm.net, and the period can be made to suit your needs.

LED Brake Light Side

Installation

The Aluminum Flashing-Steady LED Brake Light is available in three different installation options.

One option has two 1/4" holes on either end for mounting. You can customize brackets for it, and attach it however you like. Since it is poured epoxy inside an aluminum channel, the light is very rugged, and it can be mounted outside or inside your vehicle.
LED Brake Light

The next option uses brackets with suction cups attached to both ends of the light for attachment to the inside of your vehicle's rear window. The brackets can be rotated to allow the light to point straight back.
LED Brake Light

A third option has brackets with magnetic cups attached to both ends of the light for attachment to the exterior of the vehicle. The brackets can be rotated to aim the light to your satisfaction, and they easily allow the magnets to attach to the curve of your vehicle. In additon, the magnetic cups have black felt on the bottom to prevent any possibility of scratching your vehicle's finish. Click the images below for larger photos.

Porsche 356 Roadster Installation...

(click for larger images)

DC Plug and Jack

The Aluminum Flashing-Steady LED Brake Light receives power from one of your existing brake lights or the brake light switch. Its power is feed through a DC plug and jack. The jack is permanently installed in your vehicle and is located in an area of your vehicle that is easily accessible for the plug from the brake light to connect up to. This allows for easy detachment if you would like to remove it for example, at an auto show event. The wire length of the brake light to the plug is 6 feet, and the length of wire attached to the jack is also 6 feet. So the total wire length is 12 feet.

LED Brake Light plug and jack

What others have said...

Comments in regards to installation on Porsche 356 Roadster, 10/05/2010.....

I will say it is a great system. It is like the dimensions of the bracket were designed specifically for the space below the grill. It fits perfectly there and the design allows you to easily adjust the angle of the light bar to optimally point "rearward" for the best results. The 10 leds are very large as you can see and the amount of light output is very impressive. The magnet mount worked great for me. The electrical hookup was easy. I just used two tap slice crimp-on connectors and tapped into one of the brake light wires and also the brake light ground wire near the housing at the rear of the car. I have the two second flashing version and feel that has an advantage for getting attention.

This was posted to the 356 Porsche registry on 10/31/04.....

I just uninstalled the '3rd brake light from Lewryn' and installed the new Topserve model. This is the one that is hard wired and not inertia based. This unit flashes for an adjustable period of time and then goes to steady on. It is installed in my 6v coupe. The installation was a breeze as I had already run the Lewreyn wiring. The output is fantastic. Our club, Typ 356 Northeast, went on a fall drive today and many remarked as to the brightness and the eye catching flash of the unit. It seems like a well made, circuit board based, high tech light. It is not just a string of LED's - it also has a circuit board that drives the larger LED's. Like Joe's Headlight relay - It delivers what it promises, a r_e_a_l safety feature for our cars.

This was posted to the 356 Porsche registry on 11/25/04.....

Great luck with the TOPSERVE. Very bright and adjustable. Replaced the Lewryn which was not bright enough.

What Your Order Includes...

A 100% operationally tested Aluminum Flashing-Steady LED Brake Light
Complete operation and easy installation instructions
Quick delivery within 5-7 days
Emailed receipt and customer support
30 Day Risk Free Money Back Warranty

Look at Top Serve's reviews from eBay! eBay Customer Reviews

Let the Aluminum Flashing-Steady LED Brake Light benefit you by increasing your visibility to following drivers! You can easily install this LED light yourself! I guarantee you that these are the brightest LEDs you have ever seen or your money back!

Order the Aluminum Flashing-Steady LED Brake Light now for only $119.99!
Order more than one, and shipping on the second one is free!

Click Here to Order your Aluminum Flashing-Steady LED Brake Light ...

Ordering Online and by Mail

Top Serve uses Paypal as its secure online credit card merchant. Paypal is very secure and easy to use. Simply follow the instructions after clicking on the shopping cart.

Payment by Mail
This information will be sent via email to topserve@tm.net

Because we value trust with our customers, we give you the option of whether or not you would like us to ship out your order before your payment arrives. When this form is received your order will be processed promptly.

Please fill out the following information.

Name:

E-Mail:

Do you want us to send out your order before we receive payment?

Yes, please send my order out immediately. Check's in the mail.
No, please wait until my payment arrives.

What would you like to order? Please indicate quantity as well.

Ship To:

Address:

City:

State:

Zip Code:

What type of payment will you be sending?
Personal Check
Money Order

Please make the check or M.O. made payable to: Top Serve

and mail to:

Top Serve LLC
1730 Summit Street
Holland, MI 49423
USA

Shipping

Shipping charge for the Aluminum Flashing-Steady LED Brake Light is $9.50 for U.S. and Canada. Your order will be shipped via U.S. mail and delivered within 5-7 days. After you order, you will receive an emailed receipt confirming your purchase.

International Orders

Shipping charge is $12.50. Your order will be shipped via US Airmail and delivered within 5-9 days. After you order, you will receive an emailed receipt confirming your purchase.

International Click Here to Order (Outside U.S. and Canada)

Money Back Guarantee

Your purchase is risk free! If you are not 100% satisfied with your order, just send it back to the return address on your package within 30 days for a full refund minus shipping.

Top Serve LLC
1730 Summit Street
Holland, MI 49423

Thank You!

Other Products Contact MC Brake Flasher